Console Seriale

Da Vocesuip.

I Fritz! Box possiedono un collegamento per Console seriale, che può essere attivata facilmente.

Indice

Hardware

Tramite un RS232-Seriale (con soltanto 3 collegamenti: TxD, RxD e GND) senza trasduttori livellati si può realizzare l'interfaccia che funziona con livelli LVTTL. Per collegare questa interfaccia con un pc, hai bisogno così di un trasduttore del livello su RS232-Standard (da -3 a -12V/ da +3 a +12V). Puoi seguire una delle seguenti modalità:

1 Autocostruzione dell'interfaccia con un integrato MAX3232CPE o similare, da alcuni condensatori e da alcuni collegamenti sulla piastra madre del fritz!box

2 Uso di un cavo dati pratico e semplice (seriale o USB per il collegamento al pc), che uno può trovare su eBay con spedizione compresa a 5-6€ (cerca cavi Siemens).

Connessioni

Il collegamento è nella parte anteriore della piastra (nel bordo vicino ai LED). Ciò che interessa sono i quattro fori, che sono allineati con trama 2,54mm. Per un migliore utilizzo potete costruire il connettore prendendolo da una vecchia scheda di un pc o una scheda audio, occorrono 4 pin e si collegano come raffigurato sotto.

Schema (visto del lato componente):

   1  2  3  4
  []  o  o  o

   3  R  T  G
   .  x  x  N
   3  D  D  D
   V

Illustrazione dei collegamenti seriali al FBF WLAN

Attenzione ! Per il FRITZ!Box 7050, il collegamento è in un altro posto, trasversale alla piastra. È adatto per 3.3 V quindi verso il pinboard posteriore:

Illustrazione collegamento seriale del FBF 7050

Posizione del collegamento con il FRITZ! Box Fon WLAN 7170, a sinistra dal centro:

Illustrazione collegamento seriale FBF 7170

Nel FRITZ! Box SL non vi è la Console seriale nella piastra, per cui si devono saldare i contatti sotto la piastra: Illustrazione collegamento seriale FB SL (Lato saldature)

Del FRITZ! Box SL ne esistono parecchie versioni, puoi non trovare i contatti oppure trovare i contatti come gli apparecchi sopradescritti.

Cavo Dati

Sono stati utilizzati finora tre cavi dati differenti, due RS-232 e uno USB. In dettaglio:

  • Cavo originale Siemens per la serie x45
  • Cavo non originale RS232 per Siemens x55-Serie
  • Cavo non originale USB per i Siemens della serie x55

I pin nel cavo non originale RS232 sono DataIn, DataOut e GND, da collegare rispettivamente secondo quest'ordine Rxd, Txd e GND al fritz!box.

Con il cavo della Siemens USB inserire una resistenza di Pull-Up per i 3.3V (per esempio 4.7kOhm o 10kOhm) tra i pin UBat e DataOut. Il cavo USB è un convertitore seriale tipo PL2303. Sotto Linux è “plug and play”, mentre esiste un driver per Windows.

MAX 232

Chi si vuol costruire il cavo da solo, basta che vada a cercare il data sheet dell'integrato MAX3232CPE (variante DIL 3.3V) su http://www.maxim-ic.com e assemblare il circuito così come indicato.

Software

Sia il Bootloader ADAM2 che i firmware AVM si possono raggiungere attraverso la Console Seriale e sono inoltre ancora raggiungibili attraverso la configurazione di rete.

Regolazioni

Per collegare la prima volta la Console seriale dobbiamo settare le porte di comunicazione del terminale ossia della nostra porta COM sul pc. Setta la porta dove è collegato il cavo con i seguenti parametri 38400, N, 8. Ricorda: solitamente il pc utilizza un buffer di memoria, che invia le istruzioni e le esegue mettendole in coda alle prime.

Domande

Come può la Console seriale essere disattivata, per usare l'interfaccia web?

L'esempio qui sotto raffigura il tipo di collegamento che si può ottenere.

ADAM2 Revision TI:0.18.01 AVM: Version:93
(C) Copyright 1996-2003 Texas Instruments Inc. All Rights Reserved.
(C) Copyright 2003 Telogy Networks, Inc.
(C) Copyright 2003-2004 AVM

AVM_Ar7 >
Press any key to abort OS load, or wait 5 seconds for OS to boot...
Launching kernel decompressor.
Kernel decompressor was successful ... launching kernel.

LINUX started...
Config serial console: ttyS0,38400
prom_init: local_env_buffer 930 used (max 2048)
CPU revision is: 00018448
Primary instruction cache 16kb, linesize 16 bytes (4 ways)
Primary data cache 16kb, linesize 16 bytes (4 ways)
Number of TLB entries 16.
Linux version 2.4.17_mvl21-malta-mips_fp_le (jpluschke@EmbeddedVM) (gcc version 3.3.2) #939-2 Fri Jan 13 16:46:35 CET 2006
Reset Status: SW reset 1
DEBUG: Bring MDIO out of reset.
Determined physical RAM map:
 memory: 14000000 @ 00000000 (reserved)
 memory: 00020000 @ 14000000 (ROM data)
 memory: 00fe0000 @ 14020000 (usable)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line:
calculating r4koff... 000b71b0(750000)
CPU frequency 150.00 MHz
Calibrating delay loop... 149.91 BogoMIPS
Freeing Adam2 reserved memory [0x14001000,0x0001f000]
Memory: 14608k/16384k available (1240k kernel code, 1776k reserved, 75k data, 44k init)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
Checking for 'wait' instruction...  available.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Disabling the Out Of Memory Killer
devfs: v1.7 (20011216) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
Squashfs 2.1-r2 (released 2004/12/15) (C) 2002-2004 Phillip Lougher
pty: 32 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with no serial options enabled
ttyS00 at 0xa8610e00 (irq = 15) is a 16550A
block: 64 slots per queue, batch=16
Universal TUN/TAP device driver 1.4 (C)1999-2001 Maxim Krasnyansky
resize flash to 0x400000 Bytes
avalanche flash device: 0x400000 at 0x10000000.
 Amd/Fujitsu Extended Query Table v1.1 at 0x0040
Physically mapped flash:0: Swapping erase regions for broken CFI table.
number of CFI chips: 1
Looking for mtd device :mtd0:
Found a mtd0 image (0xc0000), with size (0x300000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x000c0000-0x003c0000 : "mtd0"
Looking for mtd device :mtd1:
locking for hidden SquashFs image (0x90010000 - 0x900c0000)
hidden SquashFs image found at 0xb009d100
add to memory config: hidden squashfs 0x9009d100-0x900c0000
Found a mtd1 image (0x10000), with size (0xb0000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00010000-0x000c0000 : "mtd1"
Looking for mtd device :mtd2:
Found a mtd2 image (0x0), with size (0x10000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00000000-0x00010000 : "mtd2"
Looking for mtd device :mtd3:
Found a mtd3 image (0x3c0000), with size (0x20000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x003c0000-0x003e0000 : "mtd3"
Looking for mtd device :mtd4:
Found a mtd4 image (0x3e0000), with size (0x20000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x003e0000-0x00400000 : "mtd4"
Found a mtd5 image (0x9d100), with size (0x22f00).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x0009d100-0x000c0000 : "mtd5"
mtd: partition "mtd5" doesn't start on an erase block boundary -- force read-only
Found a mtd6 image (0x9d100), with size (0x322f00).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x0009d100-0x003c0000 : "mtd6"
mtd: partition "mtd6" doesn't start on an erase block boundary -- force read-only
TFFS: tiny flash file system driver. GPL (c) AVM Berlin (Version 2.0)
      mount on mtd3 and mtd4 (double buffering)
Adam2 environment variables API installed.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 2048)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
Initializing the WAN Bridge.
Please set the MAC Address for the WAN Bridge.
Set the Environment variable 'wan_br_mac'.
MAC Address should be in the following format: xx.xx.xx.xx.xx.xx
802.1Q VLAN Support v1.6  Ben Greear <greearb@candelatech.com>
vlan Initialization complete.
VFS: Mounted root (squashfs filesystem) readonly.
root device=/dev/mtdblock/0
Mounted devfs on /dev
Freeing unused kernel memory: 44k freed
[sys_reboot]: cmd=0x0
init started:  BusyBox v1.00-pre3 (2005.11.04-09:38+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5
Using /lib/modules/2.4.17_mvl21-malta-mips_fp_le/kernel/hidden/avm.o
Warning: loading avm will taint the kernel: non-GPL license -
(C) Copyright 2003, Texas InstruAR7WDT: Watchdog Driver for AR7 Hardware (Version 1.0, build: Jan 13 2006 16:48:11)
ments, Inc
(C) Copyright 2004, 2005, AVM
  See http://www.tux.org/lkml/#export-tainted for information about tainted modules
c002f000 __insmod_avm_O/lib/modules/2.4.17_mvl21-malta-mips_fp_le/kernel/hidden/avm.o_M43CCC9C7_V-1     [avm]
c002f060 __insmod_avm_S.text_L30528     [avm]
c00367c0 __insmod_avm_S.rodata_L4304    [avm]
c0037b80 __insmod_avm_S.data_L416       [avm]
AR7WDT: System Init UEberwachung 120 Sekunden

*************************************
**** adam2 environment ****
HWRevision      85
ProductID       Fritz_Box_WLAN_3030
SerialNumber    0000000000000000
annex   B
autoload        yes
bootloaderVersion       0.18.01
bootserport     tty0
bluetooth       00:04:0E:FF:FF:07
cpufrequency    150000000
firstfreeaddress        0x947310d8
firmware_version        1und1
firmware_info   21.03.97
flashsize       0x00400000
maca    00:04:0E:73:3F:3C
macb    00:04:0E:73:3F:3D
macwlan 00:04:0E:73:3F:3E
macdsl  00:04:0E:73:3F:3F
memsize 0x01000000
modetty0        38400,n,8,1,hw
modetty1        38400,n,8,1,hw
mtd0    0x900C0000,0x903C0000
mtd1    0x90010000,0x900C0000
mtd2    0x90000000,0x90010000
mtd3    0x903C0000,0x903E0000
mtd4    0x903E0000,0x90400000
my_ipaddress    192.168.178.1
prompt  AVM_Ar7
ptest
reserved        00:04:0E:FF:FF:00
req_fullrate_freq       125000000
sysfrequency    125000000
urlader-version 93
usb_board_mac   00:04:0E:73:3F:40
usb_rndis_mac   00:04:0E:73:3F:41
usb_device_id   0x3C00
usb_revision_id 0x0200
usb_device_name USB DSL Device
usb_manufacturer_name   AVM               
wlan_key        xxxxxxxxxxxxxxxxxxxxxxxxxx
*************************************

HWRevision='85'
HWSubRevision=''
ANNEX='B'
OEM='1und1'
Language='de'
Country='049'
TZ='CET-1CEST,M3.5.0,M10.5.0'
CONFIG_AB_COUNT='0'
CONFIG_ANNEX='B'
CONFIG_ASSIST='n'
CONFIG_ATA='n'
CONFIG_ATA_FULL='n'
CONFIG_AUDIO='n'
CONFIG_AURA='n'
CONFIG_BLUETOOTH='n'
CONFIG_BLUETOOTH_CTP='n'
CONFIG_BUTTON='n'
CONFIG_CAPI='n'
CONFIG_CAPI_MIPS='n'
CONFIG_CAPI_UBIK='n'
CONFIG_CAPI_XILINX='n'
CONFIG_CDROM='y'
CONFIG_CDROM_FALLBACK='n'
CONFIG_DECT='n'
CONFIG_DSL='y'
CONFIG_ENVIRONMENT_PATH='/proc/sys/dev/adam2'
CONFIG_ETH_COUNT='2'
CONFIG_FIRMWARE_URL='http://www.avm.de/fritzbox-firmware-update.php?hardware=85&oem=1und1&language=de&country='
CONFIG_FON='n'
CONFIG_HOMEI2C='n'
CONFIG_HOSTNAME='fritz.box'
CONFIG_I2C='n'
CONFIG_INSTALL_TYPE='ar7_4MB_2eth_wlan_60396'
CONFIG_LED_NO_DSL_LED='n'
CONFIG_MEDIACLI='n'
CONFIG_MEDIASRV='n'
CONFIG_NAND='n'
CONFIG_NFS='n'
CONFIG_OEM_DEFAULT='avm'
CONFIG_PRODUKT='Fritz_Box_3030'
CONFIG_PRODUKT_NAME='FRITZ!Box WLAN 3030 (UI)'
CONFIG_RAMSIZE='16'
CONFIG_ROMSIZE='4'
CONFIG_SERVICEPORTAL_URL='http://www.avm.de/fritzbox-service-portal.php?hardware=85&oem=1und1&language=de&country='
CONFIG_STOREUSRCFG='y'
CONFIG_SUBVERSION=''
CONFIG_UBIK2='n'
CONFIG_USB='y'
CONFIG_USB_HOST_AVM='n'
CONFIG_USB_HOST_TI='n'
CONFIG_USB_PRINT_SERV='n'
CONFIG_USB_STORAGE='n'
CONFIG_USB_WLAN_AUTH='n'
CONFIG_VERSION='03.97'
CONFIG_VERSION_MAJOR='21'
CONFIG_VLYNQ0='1'
CONFIG_VLYNQ1='0'
CONFIG_VPN='n'
CONFIG_WLAN='y'
CONFIG_WLAN_GREEN='n'
CONFIG_WLAN_WDS='n'
CONFIG_XILINX='n'
*************************************

Using /lib/modules/2.4.17_mvl21-malta-mips_fp_le/kernel/hidden/avalanche_cpmac.o
Warning: loading avalanche_cpmac will taint the kernel: non-GPL license -
(C) Copyright 2003, Texas Instruments, Inc
(C) Copyright 2004, AVMcpmac .bss-address: 0xc0050cbc (&cpmac_cpu_freq - 0x4)

  See http://www.tux.org/lkml/#export-tainted for information about tainted modules
 eth0 irq= 0 io=a8610000
 eth1 irq= 0 io=a8612800
Installed 2 cpmac instances.
c003d060 __insmod_avalanche_cpmac_S.text_L64304 [avalanche_cpmac]
c003d000 __insmod_avalanche_cpmac_O/lib/modules/2.4.17_mvl21-malta-mips_fp_le/kernel/hidden/avalanche_cpmac.o_M43CCC9C7_V-1     [avalanche_cpmac]
c004ff50 __insmod_avalanche_cpmac_S.data_L1104  [avalanche_cpmac]
c004cbb0 __insmod_avalanche_cpmac_S.rodata_L13216       [avalanche_cpmac]
Using /lib/modules/2.4.17_mvl21-malta-mips_fp_le/kernel/hidden/avalanche_vlynq.o
Warning: loading avalanche_vlynq will taint the vlynq_dev_init: 1/2 VLYNQs, mask 0x0001
kernel: non-GPL GPIO pin reset, bit license - (C) Co6
pyright 2003, TeSetup registers for VLYNQ0
xas Instruments,Set local_mem.RxSize to 0x1000000
 Inc
(C) CopyriVLYNQ_TXMAP_REG = 4000000
ght 2004, AVM
 VLYNQ_R_RXMAP_OFFSET_REG(map=1) = c0000000
 See http://www.VLYNQ_R_RXMAP_SIZE_REG(map=1) = 40000
tux.org/lkml/#exVLYNQ_R_RXMAP_OFFSET_REG(map=2) = f0000000
port-tainted forVLYNQ_R_RXMAP_SIZE_REG(map=2) = 22000
 information aboVLYNQ_R_TXMAP_REG = 0
ut tainted modulVLYNQ_RXMAP_OFFSET_REG(map=1) = 14000000
es
VLYNQ_RXMAP_SIZE_REG(map=1) = 1000000
VLYNQ_REV_REG = 1010b
VLYNQ0: init succeeded!
vlynq init done
VLYNQ0: Misc device vlynq0 registered, minor #63. (0)
VLYNQ0: Running on IRQ 29.
VLYNQ1: Misc device vlynq1 registered, minor #62. (0)
VLYNQ1: Init failed!
c0055000 __insmod_avalanche_vlynq_O/lib/modules/2.4.17_mvl21-malta-mips_fp_le/kernel/hidden/avalanche_vlynq.o_M43CCC9C7_V-1     [avalanche_vlynq]
c0055060 __insmod_avalanche_vlynq_S.text_L7856  [avalanche_vlynq]
c0056f30 __insmod_avalanche_vlynq_S.rodata_L2064        [avalanche_vlynq]
c0057a30 __insmod_avalanche_vlynq_S.data_L1168  [avalanche_vlynq]
Using /lib/modules/2.4.17_mvl21-malta-mips_fp_le/kernel/drivers/net/avalanche_usb/avalanche_usb.o
Warning: loading avalanche_usb will taint the kernel: non-GPL license - ProprietAVM netusb, revision 02.01.06
ary
  See http:
//www.tux.org/lkInitializing USB CDC/CDROM driver (starting in CDC mode)...
ml/#export-taint
ed for informatinetusb: device_id=0x3c00 , revision_id=0x0200
on about tainted modules
Loaded.
c005a000 __insmod_avalanche_usb_O/lib/modules/2.4.17_mvl21-malta-mips_fp_le/kernel/drivers/net/avalanche_usb/avalanche_usb.o_M43CCC9C9_V-1      [ava
lanche_usb]
c005a060 __insmod_avalanche_usb_S.text_L29488   [avalanche_usb]
c00613b0 __insmod_avalanche_usb_S.rodata_L2624  [avalanche_usb]
c0061df0 __insmod_avalanche_usb_S.data_L2912    [avalanche_usb]
usb: CDROM Fallback=n ISO=/lib/modules/cdrom.iso
attempting to load DSL Firmware '/lib/modules/ar0700xx.bin'
**** ANNEX: 'B'
*************************************
setting DSL Firmware to Annex B
Using /lib/modules/2.4.17_mvl21-malta-mips_fp_le/kernel/drivers/atm/tiatm.o
Warning: loading tiatm will taint the kernel: non-GPL license -
(C) Copyright 2003, Texas Instruments, Inc
(C) Copyright 2004, AVM

  See hregistered device TI Avalanche SAR
ttp://www.tux.ortiatm driver (patch_annex=0xc0079500)
g/lkml/#export-tSangam detected
ainted for information about tainted modules
PM_STATUS2(before switch on) = 0x03
12 Volt:up korrekt 1.5 Volt: up korrekt Fuse Mode is disabled
PM_STATUS2(after switch on) = 0x03
12 Volt:up korrekt 1.5 Volt: up korrekt Fuse Mode is disabled
power up success !
#### DSP Core voltage set to 1,5 V ####
DSP binary filesize = 248556 bytes
avm event register
Texas Instruments ATM driver: version:[4.06.04.12]
c0065000 __insmod_tiatm_O/lib/modules/2.4.17_mvl21-malta-mips_fp_le/kernel/drivers/atm/tiatm.o_M43CCC9C7_V-1    [tiatm]
c0065060 __insmod_tiatm_S.text_L68384   [tiatm]
c0075ba0 __insmod_tiatm_S.rodata_L7392  [tiatm]
c0077af0 __insmod_tiatm_S.data_L6672    [tiatm]
Using /lib/modules/2.4.17_mvl21-malta-mips_fp_le/kernel/drivers/dsld/kdsldmod.o
Warning: loading kdsldmod will taint the kernel: no license
  See http://www.tux.org/lkml/#export-tainted for information about tainted modules
kdsldmod: init start
kdsld: cache_create(datapipe)
kdsld: cache_create(datapipe_mod)
kdsld: cache_create(ipaccessset)
kdsld: cache_create(ipaccessrule)
kdsld: cache_create(ipfragid)
kdsld: cache_create(ipmasqentry)
kdsld: cache_create(ipmasqfwinfo)
kdsld: cache_create(ipmasqigdpm)
kdsld: cache_create(ipmasqappldata)
kdsld: cache_create(dnsmasqentry)
kdsld: cache_create(dnsstaticentry)
kdsld: cache_create(pingerentry)
kdsld: cache_create(pingerwaiter)
kdsld: cache_create(iprouteset)
kdsld: DATAPIPE: with header optimization
kdsld_thread: start
kdsld: PPP led: off (value=0)
kdsldmod: init done
c00ce870 __insmod_kdsldmod_S.rodata_L25488      [kdsldmod]
c00d4c00 __insmod_kdsldmod_S.data_L56752        [kdsldmod]
c007e060 __insmod_kdsldmod_S.text_L329712       [kdsldmod]
c007e000 __insmod_kdsldmod_O/lib/modules/2.4.17_mvl21-malta-mips_fp_le/kernel/drivers/dsld/kdsldmod.o_M43CCC9C6_V-1     [kdsldmod]
2002-09-08 14:00:14 cltmgr: csock: using poll
Sep  8 14:00:14 cltmgr[292]: csock: using poll
Couldn't load shared library libavmssl.so
File not found
2002-09-08 14:00:14 cltmgr: process priority is 19
Sep  8 14:00:14 cltmgr[292]: process priority is 19
MAC WLAN:       00:04:0E:73:3F:3E
Using /lib/modules/2.4.17_mvl21-malta-mips_fp_le/kernel/drivers/wlan/tiap.o
Warning: loading tiap will taint the kernel: non-GPL license -
(C) Copyright 2003, 2004, Texas Instruments, Inc
(C) Copyright 2005, AVM

  See http://www.tux.org/lkml/#export-tainted for information about tainted modules
Sep  8 14:00:16 cltmgr[294]: box init csock_add_fd  ok
Sep  8 14:00:16 cltmgr[294]: POWER led: on (value=1)
Sep  8 14:00:16 cltmgr[294]: status change eth-interfaces
WSTART (Jan 11 2006 11:55:25)wstart: config ok(1)
*** sending hello msg with cipher  = 1 SecurityType = 1***
*** sending hello msg with cipher  = 4 SecurityType = 8***
wpa auth:waiting for driver to come up...
Wstart - made configure_wpa_authenticator
194: 802.11d is disabled
194: 802.11h is disabled
194: For SSID 0 vlan tag received is 0
194: wdrv_dbMainInit : WME disabled
194: wdrv_dbMainInit: wdsEnabled=0
194: Configuration succeeded !!!
remote_vlynq_dev_reset_ctrl(0(VLYNQ0), IN_RESET)
gpio[a8610904] &= ~(1 << 6);
Resetting the remote device.
remote_vlynq_dev_reset_ctrl: done
remote_vlynq_dev_reset_ctrl(0(VLYNQ0), OUT_OF_RESET)
Un-resetting the remote device...
GPIO pin reset, bit 6
Setup registers for VLYNQ0
Set local_mem.RxSize to 0x1000000
VLYNQ_TXMAP_REG = 4000000
VLYNQ_R_RXMAP_OFFSET_REG(map=1) = c0000000
VLYNQ_R_RXMAP_SIZE_REG(map=1) = 40000
VLYNQ_R_RXMAP_OFFSET_REG(map=2) = f0000000
VLYNQ_R_RXMAP_SIZE_REG(map=2) = 22000
VLYNQ_R_TXMAP_REG = 0
VLYNQ_RXMAP_OFFSET_REG(map=1) = 14000000
VLYNQ_RXMAP_SIZE_REG(map=1) = 1000000
VLYNQ_REV_REG = 1010b
VLYNQ0: init succeeded!
vlynq init done
VLYNQ re-initialized.
Test, reading from a4000004... result = 0xeafffffe
remote_vlynq_dev_reset_ctrl: done
204:
dda: tiwlan0 in initializing Succeeded wireless extensions: ret = 0
wlan started (OK)
Wstart - made configure_and_start_ap_driver
WSTART: done(0)
WLAN is enabled
tiwlan0 device is activated
Sep  8 14:00:23 websrv[326]: csock: using poll
Sep  8 14:00:24 igdd[330]: csock: using poll
2002-09-08 14:00:25 multid: startup (Jan 11 2006 11:54:02)
Sep  8 14:00:25 multid[334]: startup (Jan 11 2006 11:54:02)
2002-09-08 14:00:25 multid: csock: using poll
Sep  8 14:00:25 multid[334]: csock: using poll
Couldn't load shared library libavmssl.so
File not found
request_module(lan)
Sep  8 14:00:26 request_module(wlan)
multid[338]: if_setup: lan:0: SIOCSIFADDR failed - No such device (19)
Sep  8 14:00:26 device usbrndis entered promiscuous mode
multid[338]: brilan: port 1(usbrndis) entering learning state
dge lan has 0 indevice tiwlan0 entered promiscuous mode
terfaces only_thlan: port 2(tiwlan0) entering learning state
is=<null>
Sep device wdsup0 entered promiscuous mode
 8 14:00:26 multid[338]: add usbrndis to bridge lan
Sep  8 14:00:26 multid[338]: add tiwlan0 to bridge lan
Sep  8 14:00:26 multid[338]: add wdsup0 to bridge lan
wdsup0 device is activated
lan: port 3(wdsup0) entering learning state
Sep  8 14:00:26 device wdsdw0 entered promiscuous mode
multid[338]: addwdsdw0 device is activated
 wdsdw0 to bridglan: port 4(wdsdw0) entering learning state
e lan
Sep  8 14:00:26 device wdsdw1 entered promiscuous mode
multid[338]: add wdsdw1 to bridge lan
wdsdw1 device is activated
lan: port 5(wdsdw1) entering learning state
Sep  8 14:00:26 device wdsdw2 entered promiscuous mode
multid[338]: addwdsdw2 device is activated
 wdsdw2 to bridglan: port 6(wdsdw2) entering learning state
e lan
2002-09-08 14:00:26 dsld: csock: using poll
Sep  8 14:00:26 dsld[343]: csock: using poll
Couldn't load shared library libavmssl.so
File not found
Sep  8 14:00:26 device wdsdw3 entered promiscuous mode
multid[338]: addwdsdw3 device is activated
 wdsdw3 to bridglan: port 7(wdsdw3) entering learning state
e lan
Sep  8 14:00:26 multid[338]: br_del_if: del bridge eth0 failed - Invalid argument (22)
Sep  8 14:00:27 multid[338]: static routes: 0 deleted (0 failed), 0 added (0 failed)
Sep  8 14:00:27 multid[338]: static routes: 0 deleted (0 failed), 0 added (0 failed)
Sep  8 14:00:27 multid[338]: DHCPC on lan
Sep  8 14:00:27 multid[338]: DHCPD on lan:0 skipped, is virtual interface
Sep  8 14:00:27 multid[338]: DHCPC: lan: state init
Sep  8 14:00:27 multid[338]: DHCPC: lan reset ip address
Sep  8 14:00:27 multid[338]: static routes: 0 deleted (0 failed), 0 added (0 failed)
Sep  8 14:00:27 multid[338]: 1 Packets
Sep  8 14:00:27 multid[338]: DHCPC: lan: state init, got event discover-sent
Sep  8 14:00:27 multid[338]: DHCPC: lan: state selecting
Sep  8 14:00:27 multid[338]: DDNS: dbs-server.dyndns.org
Sep  8 14:00:27 multid[338]: DDNS: 1 accounts
Sep  8 14:00:27 multid[338]: ONLINE: script /bin/onlinechanged not found.
2002-09-08 14:00:27 dsld: startup (Jan 11 2006 11:54:15)
Sep  8 14:00:27 dsld[343]: startup (Jan 11 2006 11:54:15)
Sep  8 14:00:27 multid[338]: interface eth0 up.
Sep  8 14:00:27 multid[338]: static routes: 0 deleted (0 failed), 0 added (0 failed)
device eth0 entered promiscuous mode
Sep  8 14:00:27 dsld[346]: DSL Mac 00:04:0e:73:3f:3c
run_clock demon started

AR7WDT: System Init UEberwachung abgeschlossen (95630 ms noch verfuegbar)
Sep  8 14:00:27 dsld[346]: VOIP Mac 00:04:0e:73:3f:40
Sep  8 14:00:28 dsld[346]: speed 7200/1056 (LAN)
Sep  8 14:00:28 kdsld: showtime
dsld[346]: showtime
Sep  8 14:00:28 multid[338]: interface eth1 up.
Sep  8 14:00:28 multid[338]: static routes: 0 deleted (0 failed), 0 added (0 failed)
Sep  8 14:00:28 dsld[34kdsld: dev_add_pack(etherip)
6]: normal schedkdsld: VCCuling
 0: registered (eth0)

Please press Enter to activate tkdsld: 0: VPI/VCI 0/0 RBE internet 00:04:0e:73:3f:3c (14,14)
his console. kdsld: internet: set_rcv_ipaddr: 192.168.179.1
kdsld: interface 0 created.
Sep  8 14:00:28 kdsld: setup done.
multid[338]: intrequest_module(wlan)
erface dsl new.
Sep  8 14:00:28 multid[338]: bridge lan has 7 interfaces only_this=dsl
Sep  8 kdsld: DHCPC: internet: state init
14:00:28 multid[kdsld: DHCPC: internet: state init, got event discover-sent
338]: br_del_if:kdsld: DHCPC: internet: state selecting
 del bridge eth0 failed - Invalid argument (22)
Sep  8 14:00:28 multid[338]: static routes: 0 deleted (0 failed), 0 added (0 failed)
Sep  8 14:00:28 multid[338]: interface dsl up.
Sep  8 14:00:28 multid[338]: static routes: 0 deleted (0 failed), 0 added (0 failed)
Sep  8 14:00:28 multid[338]: DHCPC: lan: state selecting, got event timeout
Sep  8 14:00:28 multid[338]: DHCPC: lan: state selecting, got event discover-sent
Sep  8 14:00:29 websrv[326]: startup (Jan 11 2006 11:54:00)
kdsld: DHCPC: internet: state selecting, got event timeout
kdsld: DHCPC: internet: state selecting, got event discover-sent
lan: port 1(usbrndis) entering forwarding state
lan: topology change detected, propagating
lan: port 2(tiwlan0) entering forwarding state
lan: topology change detected, propagating
lan: port 3(wdsup0) entering forwarding state
lan: topology change detected, propagating
lan: port 4(wdsdw0) entering forwarding state
lan: topology change detected, propagating
lan: port 5(wdsdw1) entering forwarding state
lan: topology change detected, propagating
lan: port 6(wdsdw2) entering forwarding state
lan: topology change detected, propagating
lan: port 7(wdsdw3) entering forwarding state
lan: topology change detected, propagating
Sep  8 14:00:34 igdd[330]: UPNP-Description:FRITZ!Box-00:04:0E:73:3F:3C UPnP/1.0 AVM FRITZ!Box WLAN 3030 (UI) 21.03.97
Sep  8 14:00:34 igdd[330]: OemStringData.MAC:00040E733F3C
Sep  8 14:00:34 igdd[330]: startup (Jan 11 2006 11:54:01)
kdsld: DHCPC: internet: state selecting, got event timeout
kdsld: DHCPC: internet: state selecting, got event discover-sent
Sep  8 14:00:35 igdd[330]: check_noip_devices: new iface eth0 found or changed
Sep  8 14:00:35 igdd[330]: check_noip_devices: new iface eth1 found or changed
Sep  8 14:00:35 igdd[330]: check_noip_devices: new iface usbrndis found or changed
Sep  8 14:00:35 igdd[330]: check_noip_devices: new iface tiwlan0 found or changed
Sep  8 14:00:35 igdd[330]: check_noip_devices: new iface wdsup0 found or changed
Sep  8 14:00:35 igdd[330]: check_noip_devices: new iface wdsdw0 found or changed
Sep  8 14:00:35 igdd[330]: check_noip_devices: new iface wdsdw1 found or changed
Sep  8 14:00:35 igdd[330]: check_noip_devices: new iface wdsdw2 found or changed
Sep  8 14:00:35 igdd[330]: check_noip_devices: new iface wdsdw3 found or changed
Sep  8 14:00:35 igdd[330]: upnp_server_start: We don't have any iface at this time, but waiting
Sep  8 14:00:37 multid[338]: DHCPC: lan: state selecting, got event timeout
Sep  8 14:00:37 multid[338]: DHCPC: lan: state selecting, got event discover-sent



BusyBox v1.00-pre3 (2005.11.04-09:38+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

HWRevision='85'
HWSubRevision=''
ANNEX='B'
OEM='1und1'
Language='de'
Country='049'
TZ='CET-1CEST,M3.5.0,M10.5.0'
CONFIG_AB_COUNT='0'
CONFIG_ANNEX='B'
CONFIG_ASSIST='n'
CONFIG_ATA='n'
CONFIG_ATA_FULL='n'
CONFIG_AUDIO='n'
CONFIG_AURA='n'
CONFIG_BLUETOOTH='n'
CONFIG_BLUETOOTH_CTP='n'
CONFIG_BUTTON='n'
CONFIG_CAPI='n'
CONFIG_CAPI_MIPS='n'
CONFIG_CAPI_UBIK='n'
CONFIG_CAPI_XILINX='n'
CONFIG_CDROM='y'
CONFIG_CDROM_FALLBACK='n'
CONFIG_DECT='n'
CONFIG_DSL='y'
CONFIG_ENVIRONMENT_PATH='/proc/sys/dev/adam2'
CONFIG_ETH_COUNT='2'
CONFIG_FIRMWARE_URL='http://www.avm.de/fritzbox-firmware-update.php?hardware=85&oem=1und1&language=de&country='
CONFIG_FON='n'
CONFIG_HOMEI2C='n'
CONFIG_HOSTNAME='fritz.box'
CONFIG_I2C='n'
CONFIG_INSTALL_TYPE='ar7_4MB_2eth_wlan_60396'
CONFIG_LED_NO_DSL_LED='n'
CONFIG_MEDIACLI='n'
CONFIG_MEDIASRV='n'
CONFIG_NAND='n'
CONFIG_NFS='n'
CONFIG_OEM_DEFAULT='avm'
CONFIG_PRODUKT='Fritz_Box_3030'
CONFIG_PRODUKT_NAME='FRITZ!Box WLAN 3030 (UI)'
CONFIG_RAMSIZE='16'
CONFIG_ROMSIZE='4'
CONFIG_SERVICEPORTAL_URL='http://www.avm.de/fritzbox-service-portal.php?hardware=85&oem=1und1&language=de&country='
CONFIG_STOREUSRCFG='y'
CONFIG_SUBVERSION=''
CONFIG_UBIK2='n'
CONFIG_USB='y'
CONFIG_USB_HOST_AVM='n'
CONFIG_USB_HOST_TI='n'
CONFIG_USB_PRINT_SERV='n'
CONFIG_USB_STORAGE='n'
CONFIG_USB_WLAN_AUTH='n'
CONFIG_VERSION='03.97'
CONFIG_VERSION_MAJOR='21'
CONFIG_VLYNQ0='1'
CONFIG_VLYNQ1='0'
CONFIG_VPN='n'
CONFIG_WLAN='y'
CONFIG_WLAN_GREEN='n'
CONFIG_WLAN_WDS='n'
CONFIG_XILINX='n'
ermittle die aktuelle TTY
tty is "/dev/tts/0"
ESC[50;132qSerielles Terminal
# god
-sh: god: not found
# giveall
-sh: giveall: not found
# kdsld: DHCPC: internet: state selecting, got event timeout
kdsld: DHCPC: internet: state selecting, got event discover-sent
Sep  8 14:00:52 multid[338]: DHCPC: lan: state selecting, got event timeout
Sep  8 14:00:52 multid[338]: DHCPC: lan: state selecting, got event discover-sent
kdsld: DHCPC: internet: state selecting, got event timeout
kdsld: DHCPC: internet: state selecting, got event discover-sent
Sep  8 14:01:23 multid[338]: DHCPC: lan: state selecting, got event timeout
Sep  8 14:01:23 multid[338]: DHCPC: lan: state selecting, got event discover-sent
kdsld: DHCPC: internet: state selecting, got event timeout
kdsld: DHCPC: internet: setting broadcastflag
kdsld: DHCPC: internet: state selecting, got event discover-sent
Sep  8 14:02:28 multid[338]: DHCPC: lan: state selecting, got event timeout
Sep  8 14:02:28 multid[338]: DHCPC: lan: setting broadcastflag
Sep  8 14:02:28 multid[338]: DHCPC: lan: state selecting, got event discover-sent
kdsld: DHCPC: internet: state selecting, got event timeout
kdsld: DHCPC: internet: setting broadcastflag
kdsld: DHCPC: internet: state selecting, got event discover-sent

Links

Strumenti personali